Enterasys-networks 7S4280-19-SYS Manual de usuario Pagina 94
- Pagina / 108
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7C111 Chassis Specifications and Regulatory Compliance
A-4 Specifications and Regulatory Compliance
NAC Controller Engine COM Port Pinout Assignments
TheCOMportisaserialcommunicationsportforlocalaccesstoLocalManagement.Referto
Table A‐6fortheCOMportpinassignments.
DC Output Voltage 12v
DC Output Amps 5A
Physical
Dimensions • Width: 10.65 in. (27.05 cm)
• Length: 7.3 in. (18.54 cm)
• Depth: 1.8 in (4.57 cm)
Predicted hours for Mean Time
Between Failures (MTBF)
For the MTBF hours for this module, refer to the MTBF web
site at URL
http://www.enterasys.com/support/mtbf/
Maximum Wattage 50 Watts
Environmental
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -30°C to 73°C (-22°F to 164°F)
Operating Relative Humidity 5% to 90% (non-condensing)
Minimum Air Flow 200 Linear Feet / Minute
Table A-5 NAC Controller Engine Specifications (continued)
Item Specification
Table A-6 COM Port Pin Assignments
Pin Signal Name Input/Output
1 Transmit Data (XMT) Output
2 Clear to Send (CTS) Input
3 Data Set Ready (DSR) Input
4 Receive Data (RCV) Input
5 Signal Ground (GND) NA
6 Request to Send (RTS) Output
7 Data Terminal Ready (DTR) Output
8 Data Carrier Detect (DCD) Input
- Enterasys 1
- orcontactEnterasys 5
- (Circuit Modules) 6
- (Circuit Breakers) 6
- VCCI Notice 7
- BSMI EMC Statement — Taiwan 7
- Safety Information 7
- Class 1 Laser Transceivers 7
- Declaration of Conformity 8
- Contents 11
- Chapter 5: Troubleshooting 12
- About This Guide 17
- Related Documents 18
- Typographical Conventions 19
- Commonly Used Acronyms 19
- Getting Help 20
- Introduction 21
- The N1-7C111 Chassis 22
- The NAC Controller PEP 22
- Overview 23
- 1-4 Introduction 24
- 1-6 Introduction 26
- Standards Compatibility 27
- LANVIEW Diagnostic LEDs 27
- 1-8 Introduction 28
- Site Guidelines 29
- Configuration Guidelines 30
- LANVIEW LEDs 30
- Link Aggregation 32
- 10BASE-T Network 32
- 100BASE-TX Network 32
- 1000BASE-T Network 32
- 1000BASE-SX/LX/ELX Network 33
- Order of Installation 36
- Installing the Rubber Feet 37
- N1 7C111 d 39
- Cooling Fans 40
- Required Tools 41
- Preparation 42
- engine o el módulo 42
- Installation 43
- (MGBIC-02) 4 Port slot 44
- Removing the Mini-GBIC 45
- Connecting to the Network 47
- Switches and End User Devices 49
- 2 Other device port 50
- 3 Release tab 52
- What Is Needed 54
- Connecting to a Modem 56
- RJ45 DB9 57
- Completing the Installation 58
- Enterasys Matrix 59
- Troubleshooting 61
- Using LANVIEW 62
- 5-2 Troubleshooting 62
- Table 5-1 LANVIEW LEDs 63
- Troubleshooting Checklist 64
- 5-6 Troubleshooting 66
- 5-8 Troubleshooting 68
- NAC Controller 74
- Setup the VLAN Configurations 84
- Physical Specifications 91
- Environmental Requirements 92
- Regulatory Requirements 92
- Specifications 93
- Specifications (continued) 94
- Item Specification 95
- Regulatory Compliance 100
- Mode Switch Bank Settings 101
- Location of Memory Modules 102
- Removing the DRAM SIMM 105
- Installing the DRAM SIMM 105
- Index-2 108
Relacionado con productos y manuales para Hardware Enterasys-networks 7S4280-19-SYS
Hardware Enterasys-networks XSR-3020 Manual de usuario
(110 paginas)
(110 paginas)
Hardware Enterasys-networks FN 100 Manual de usuario
(54 paginas)
(54 paginas)
Hardware Enterasys-networks XSR-3150 Manual de usuario
(110 paginas)
(110 paginas)
Hardware Enterasys-networks 802.1Q Manual de usuario
(82 paginas)
(82 paginas)
CST Elektrické nářadí uživatelské příručky
Začínající na S
Comentarios a estos manuales