Enterasys-networks XSR-3020 Manual de usuario Pagina 108
- Pagina / 110
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Cable, CompactFlash and Accessory Specifications
A-22
PWR ON XSR is powered up and Bootrom initialized
OFF XSR is powered down
VPN ON/OFF VPN tunnel is up/No tunnel connected
COM(munication) Blinking/OFF Port is transmitting or receiving data/idle
Ethernet Port 1, 2, 3 Amber only ON 10Base-T link is auto-detected
Green only ON 100Base-T link is auto-detected
Both ON 1000Base-T link is auto-detected
Blinking Port is transmitting or receiving data
OFF Link is down
Fiber/Copper Mini-GBIC
(Ethernet) Port
Both OFF Port is configured as copper
Link LED ON Fiber link up
TX LED
Blinking
Activity on fiber port
BRI NIM Port 0/1 Connected to
switch
BRI link is activated and ready for traffic. This LED is
located on the NIM card.
ADSL NIM 1 Blinking Line is in training mode (syncing with DSLAM)
ON Training mode complete, line is operational
OFF Line is down
ADSL NIM 2 Blinking Traffic activity in sync with data traffic
T3/E3 NIM:
•LOS (Loss of Signal)
•LOF (Loss of Frame)
•Alarm
•Enable
Red ON
Red ON
Amber ON
Green ON
XSR cannot latch onto the frequency
Both sides of link cannot synchronize frames
Error condition detected
Link is up and running
Copper Ethernet NIM Link ON
Link OFF
Activity Blinking
100Base-T link is auto-detected
10Base-T link is auto-detected
Port is transmitting or receiving data
Fiber-optic Ethernet NIM Link ON
Activity ON
100Base-F link is auto-detected
Port is transmitting or receiving data
Table A-3 LED Description (continued)
LED State Function
- X-Pedition 1
- Security Router 1
- Industry Canada Notices 5
- Class A ITE Notice 5
- Clase A. Aviso de ITE 5
- Klasse A ITE Anmerkung 5
- orcontact 6
- (Circuit Modules) 7
- (Circuit Breakers) 7
- VCCI Notice 8
- BSMI EMC Statement — Taiwan 8
- Declaration of Conformity 8
- Australian Telecom 9
- Contents 13
- Appendix A: Specifications 15
- About This Guide 17
- Getting Help 19
- Overview 21
- PSTN (for PPP) 22
- ETH2ETH1 23
- Operating System 24
- Industry-common CLI 24
- IP Protocol 24
- IP Routing 25
- SNMP and Statistics Gathering 25
- Security 26
- Frame Relay 26
- System Description 27
- XSR Getting Started Guide 1-7 27
- Quality of Service (QoS) 28
- Virtual Private Network (VPN) 28
- GRE over IPSec 29
- Dial Service 30
- Dial Backup 30
- Installation Overview 31
- 1-12 Overview 32
- Hardware Installation 33
- 2-2 Hardware Installation 34
- XSR Getting Started Guide 2-3 35
- 2-4 Hardware Installation 36
- XSR Getting Started Guide 2-5 37
- 2-6 Hardware Installation 38
- Connecting Cables 39
- SECURITY ROUTERS 40
- XSR Getting Started Guide 2-9 41
- Figure 2-16 42
- Figure 2-18, respectively 43
- Software Configuration 44
- Initializing XSR Software 46
- 3-2 Software Configuration 46
- XSR Getting Started Guide 3-3 47
- Setting the Clock 51
- Configuring the LAN Ports 52
- Configuring the WAN Ports 52
- BRI Leased Line 53
- BRI Leased Frame Relay 53
- BRI Switched Line 54
- Firewall Sample Configuration 56
- Setting Up RIP Routing 58
- Configure OSPF Routing 59
- 3-16 Software Configuration 60
- Viewing Your Configuration 61
- 3-18 Software Configuration 62
- Site regional router 64
- Configure Users and Passwords 66
- Configure LAN Interface 66
- Configure Quality of Service 66
- Apply QoS 68
- Configure More Access Lists 68
- Configure DHCP/BOOTP Relay 69
- Configure SNMP 70
- Set Up IKE Phase I Security 71
- Create a Transform Set 72
- Configure Crypto Maps 72
- 3-30 Software Configuration 74
- XSR Rebooting Characteristics 76
- Reboot Triggers 77
- Cause Boot Type 77
- 3-34 Software Configuration 78
- Bootrom Monitor Mode Commands 79
- 3-36 Software Configuration 80
- 3-38 Software Configuration 82
- 3-40 Software Configuration 84
- 3-42 Software Configuration 86
- Specifications 87
- Short-haul MTRJ 88
- Pin 1 Pin 5 90
- Pin 6 Pin 9 90
- Pins not shown are unused 96
- RX In TX Out 99
- G.703 Balun 99
- Model 460 MC 99
- Regulatory/Safety Compliance 101
- ALARM LOS 101
- ENABLE LOF 101
- Port 0 Activation LED 102
- Port 1 Activation LED 102
- Pin 8Pin 1 102
- Transmit Pair Termination 103
- Port 0 Port 1 103
- Port 1Port 0 103
- Receive Pair Termination 103
- NIM1 NIM2 107
- LED State Function 108
- Index-2 110
Relacionado con productos y manuales para Hardware Enterasys-networks XSR-3020
Hardware Enterasys-networks FN 100 Manual de usuario
(54 paginas)
(54 paginas)
Hardware Enterasys-networks XSR-3150 Manual de usuario
(110 paginas)
(110 paginas)
Hardware Enterasys-networks 802.1Q Manual de usuario
(82 paginas)
(82 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales